full information

Industrial bare board Regulated switching power supply Low interference 72W full power built-in board

The product is easy to install. And input/output terminal (2P 8mm foot/6P 4mm), which can be used with retained hole welding line.

  • Brand:

    QINXPOWER
  • Model:

    QPT70A
  • Input Voltage:

    85-264V AC or 110-370V DC.
  • Working Mode:

    AC-DC
  • Power:

    70W
  • High Isolation with Voltage:

    3000VAC
Products description

Product features:

  • 1.The product is easy to install. And input/output terminal (2P 8mm foot/6P 4mm), which can be used with retained hole welding line.
  • 2.Fixed mounting holes in the four corners which prevent power failure due to movement/vibration. For details of fixed holes, please check the size chart of below.
  • 3.Iternational Universal input voltage: 85-264V AC or 110-370V DC.
  • 4.High efficiency, high power density, low output ripple noise and high voltage output accuracy(the voltage difference between light load and full load at the output interface of the product is within 0. 1V).
  • 5.High isolation between input and ouput
  • 6.High reliability, long life, industrial design.
  • 7.Overcurrent protection, short circuit protection and overtemperature protection (temperature limit 65 degrees), output with overvoltage protection.
  • 8.Loop abnormal protection (starting protection when DC has applied voltage or when the loop works abnormally and the voltage overvoltage reaches the output overvoltage protection point).
  • 9.The output has LC-pi filter without external large-capacity filter circuit.
  • 10.Three years of quality assurance
Item Condition Common models of this series we have (we can customize any products with different output voltage and current

or other requirements according to customer’s requirements)

QPT70B-05 QPT70A-09 QPT70A- 12 QPT70A- 15 QPT70A-24 QPT70A-36
1 、Input Features
AC Input(VAC) 85-264VAC
DC Input(VDC) 110-370VDC
Frequency Range (Hz) 47-63Hz
Input Current(A) 2A/ 115VAC   1A/230VAC
Surge current(A) Cold Boot:20A/230VAC
Efficiency(TYP.) 78% 82% 83% 83% 86% 88%
Stand-by power consumptio(mW) ≤ 1W/230VAC
2 、Output Features
Output Voltage(VDC) 5V 9V 12V 15V 24V 36V
Output voltage accuracy ± 1%
Rated current(ADC) 10A 8A 6A 4.8A 3A 2A
Rated power(W) 50W 72W 72W 72W 72W 72W
Ripple&Noise(mv

p-p)

Rated input

voltage, 20MHz

bandwidth

≤50mV
Linear adjustment rate Full-load ± 1%
Load regulation 10- 100% Load ±3%
Start up and rise time Full-load 300ms, 30ms/ 115VAC    200ms, 30ms/230VAC
Retention

time(ms)

Full-load 16ms/ 115VAC  50ms/230VAC
Overload

protection

Rated input voltage 115%- 150% of the rated output power
Protection mode: hiccup mode, auto-response after removal of abnormal load
Output

Overvoltage

Protection

Voltage     Protection(V)  

7V

 

12V

 

15V

 

18V

 

27V

 

39V

Short-circuit protection  

Rated Input Voltage

Automatic recovery after long-term short circuit
Over-current protection ≥ 1. 1 Times Io
Start delay

time(ms)

 

 

Vin :230VAC

1000ms
Power-off

protection

time(ms)

 

20ms

3 、General Features
Working      temperature(C) / -30-70C
Working    humidity(RH) / 20-90%RH ,non-condensing
temperature

coefficient

/ ±0.02%/C
Storage temperature and humidity -40~+85C 10-95%RH
Switching frequency(KHz) 20-65KHz
Isolation     voltage(VAC) Input-to-output,  test lasted 60s ,≤

5mA

3000VAC
Insulation     resistance(MΩ) Input to output,

500VDC

100MΩ
Leakage   current(mA) 500VDC Input to output     ≤ 1mA/RMS
MTBF @25C 215000h
Safety level / Adaptation:CLASS B
Vibration

resistance

/ 10—500Hz 2G 10 minutes/cycle. 60 minutes each for X, Y and Z
Electro-magnetic compatibility / Adaptation:EN55022(CISPR22) Class B  EN61000-3-2-3
 

 

 

Remarks

1. Except for special instructions, the parameters of this specification are measured at 230VAC input, rated load and 25C.

2. Measurement of ripple and noise: Using a  12” twisted pair, and the terminal has two capacitors, 0. 1uF and 10uF in parallel. Measured at 20MHz bandwidth.

3.Accuracy: Including errors, linear adjustment rate and load adjustment rate.

4. The power supply should be regarded as part of the components in the system, and electro-magnetic compatibility related confirmation should be carried out with the terminal equipment.

5. Reduced output is required under low input voltage. Please refer to the reduction graph.

 

Product Packaging and Pin Definition Diagram

QPT70A T

Product selection and Notes:

  • 1.Please refer to the specifications in detail for selection and use, otherwise the reliability of power supply will    not be guaranteed.
  • 2.All parameters of this specification are measured according to the internal standards of our company.
  • 3.It is suggested that the load power of the power supply should not exceed 80% of the rated power of the power  supply.
  • 4.With multi-output power supply, each output circuit    must be loaded and used at the same time according to the corresponding ratio. The maximum current of high precision voltage (5V) group of this series of products is 1A, and more than 1A will cause permanent damage to the products.
  • 5.Our company can provide customized products.
  • 6.We reserve the right to change specifications without prior notice.
Leave a message

    To know more our power supplies/Power adapters/LED drivers/Chargers, please send email to us, we will reply to you soon.

    Related Product
    QLA05 Wholesale 3-5W High Quality AC-DC Switch power modules

    QLA05 Wholesale 3-5W High Quality AC-DC Switch power modules

    The product is easy to install and can be directly used on the mainboard.

    3W built-in bare board power supply

    3W built-in bare board power supply

    The QLA03A product is with easy installation and can be used on the mainboard with terminals directly.

    QLK17W series built-in bare board open frame power supply 17Watts

    QLK17W series built-in bare board open frame power supply 17Watts

    The QLK17W product is with easy installation. Input/output with 90 degree 2.54 row needles, which can be used for reserved hole welding wire hole.

    QLA17A series built-in bare board open frame power supply 17Watts

    QLA17A series built-in bare board open frame power supply 17Watts

    The QLA17W series product is with easy installation. Input / Output could insert terminals and Retainable hole welding wire is used.

    Industrial bare board Regulated switching power supply Low interference 72W full power built-in board

    Industrial bare board Regulated switching power supply Low interference 72W full power built-in board

    The product is easy to install. And input/output terminal (2P 8mm foot/6P 4mm), which can be used with retained hole welding line.

    QINX

    Connect With Us
    If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
    Way to contact us.

      Copyright © Qinx Technology Co., Ltd..All Rights Reserved.
      Welcome To QINX

        To know more our Power adapters/LED drivers/power supplies/Chargers, pls send email to us, we will reply you soon.

        Home

        Products

        About

        Contact